SILENT KNIGHT 4821 Instalační manuál Strana 128
- Strana / 154
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Model 4821/4820 Control/Communicator Installation Manual
6-26 150966
Note: *Type of alarm that will be sounded and displayed on the touchpad if this zone type is used.
Table 6-8: Zone Types
Zone Type Description
*Alarm
Type
Fire Use with smoke detectors that will be connected to reset smoke power
to verify alarms. See Section 4.16.1 for information about smoke
detector compatibility.
Fire
Holdup To indicate a user under duress, silent and/or invisible must be
selected.
Intrusion
Emergency Non-medical emergencies. Emergency
Panic Use for manually activated request for emergency assistance. Emergency
Burglary Use with intrusion type contacts on doors, windows, etc. Intrusion
Tamper Use to indicate that the alarm equipment enclosure had been either
tampered with or opened.
Intrusion
Gas Use with carbon monoxide, radon, and other gas detection devices. Auxiliary
Undefined Use for a condition that does not fit any of the other zone types. Auxiliary
Water This zone type should be used to indicate water has been detected at
the protected premise.
Auxiliary
Heat Use to indicate that a high temperature has been detected. Auxiliary
Cold Use to indicate that a low temperature has been detected. Fire
Sprinkler Use with sprinkler flow detectors to indicate alarm when water is
flowing.
Auxiliary
Doorbell 1 Slow two tone (ding-dong) bell sound. Auxiliary
Doorbell 2 Slow bell (ding) sound. Auxiliary
Key arming input Can be used with a mechanical key to arm and disarm areas common
to the zone.
Auxiliary
The Armed and Disarmed zone responses should have one READY and one NOT READY state each, and no
ALARM states. TROUBLE states are allowed and the key input can be supervised. Each time the key input
changes from READY to NOT READY, the system will either arm or disarm the areas assigned to the zone
using the following rules: 1) If any of the assigned areas are armed, then all areas are disarmed by the key
activation. 2) If all of the assigned areas are disarmed, then all areas are armed by the key activation. The areas
must be ready to arm in order for any arming to occur.
Reserved Do not select. Auxiliary
Door monitor Select for zones that will be used with the touchpad Door Monitor
function. Door-Monitor zones should be programmed for at least one
READY and one NOT READY state. This zone type will cause an
alarm if programmed with an ALARM state.
Auxiliary
Fire contact Use with pull stations or the fire panic key. With this zone type, smoke
power does not reset when the zone is reset.
Fire
Egress input Used for door egress request switch (Exit button). Auxiliary
Sprinkler Supervisory Select for zones that will be monitoring the sprinkler shut off valve.
This zone is typically programed to cause an alarm when the system is
armed or disarmed. Trouble tones will sound on INT1 speakers and
touchpads once the zone enters the alarm region. The 4884Bell
Module will not activate for an alarm (supervisory) on this zone.
Supervisory
- Contents 1
- Section 3 2
- Section 4 2
- Section 5 4
- Section 6 5
- Troubleshooting 6
- Section 1 7
- Introduction 7
- 1.1.1 Compatible Modules 8
- 1-4 150961 10
- 1.2 How to Use this Manual 11
- 1.4 Agency Requirements 12
- 1.4.3 UL Requirements 13
- 1.4.3.2 Grade A Mercantile 14
- 1.4.3.4 Access Control UL-294 15
- 1-10 150961 16
- Section 2 17
- Quick Start 17
- 2-2 150962 18
- 2.2 Sending Data to the Panel 19
- 2.4 Installation Records 20
- 2.4.1.1 Zone Record 22
- 4815 Expander Loop2 25
- 2-10 150962 26
- 3-2 150963 28
- 150963 3-3 29
- 3-4 150963 30
- 3.2.2 Mounting 31
- 3-6 150963 32
- 150963 3-7 33
- 3-8 150963 34
- 150963 3-9 35
- 3.4 Access Control Operation 36
- 3.4.2 End-User Operation 37
- 3.4.4 Viewing Door Status 38
- 3.4.5 Anti-Passback Feature 39
- 3-14 150963 40
- 150963 3-15 41
- 3-16 150963 42
- 150963 3-17 43
- 3-18 150963 44
- 4.3 Board Layout 46
- 150964 4-3 47
- 4.5 Power Limiting Circuits 48
- 4.6 Power Switch 49
- 4.8 Wire Routing 50
- 4.9 Current Draw Worksheets 51
- 4-8 150964 52
- 150964 4-9 53
- 4-10 150964 54
- 150964 4-11 55
- 4.10 AC Power Transformer 56
- 150964 4-13 57
- 4-14 150964 58
- 4.13 SBUS 59
- 4-16 150964 60
- Max. Distance = 500V 61
- 4.14 Touchpad Installation 62
- 4.14.3 Wiring Touchpads 63
- 4.15 Zone Installation 64
- 4.15.3 Zone Configuration 65
- 4-22 150964 66
- 150964 4-23 67
- 4-24 150964 68
- 150964 4-25 69
- 4.16.1.1 Smoke Reset Cycle 70
- 150964 4-27 71
- 4.17 Speaker Wiring 72
- 4.18 Bell Wiring 73
- 4.18.2 Commercial Bell Wiring 74
- 4.19 4884 Bell Module wiring 75
- 4-32 150964 76
- 150964 4-33 77
- 4.21 Built-in Relay 78
- 4.22 DACT Compliant Wiring 79
- Alarm Relay Trouble Relay 80
- 150964 4-37 81
- 4-38 150964 82
- 5-2 150965 84
- 5.2 Touchpad Models 86
- 6LOHQW.QL 87
- 5.3.2 Normal Display Messages 88
- 5.3.3 System Status Messages 88
- 5.4 Touchpad Buttons 89
- 5-8 150965 90
- 5.6 Interactive Menu Overview 91
- 5.7 System Operation Summary 92
- 5-12 150965 94
- 5-14 150965 96
- 5.9 System Test Descriptions 98
- 5-18 150965 100
- System Operation 101
- 5-20 150965 102
- MUTE-Exit Menu 103
- [Installer’s Code] 104
- 6.2.2.1 1-Install Device 105
- 6.2.2.2 2-Edit System Options 105
- 6.2.2.3 3-Edit Partition 106
- 6.2.2.4 4-Edit Ph. Lines 106
- 6.2.2.5 5-Reprt Accounts 107
- 6.2.2.6 6-Print Accounts 107
- 6.2.2.7 7-Edit Profiles 108
- Programming 109
- 6-8 150966 110
- 6.2.2.9 8-Edit Schedules 111
- 6.2.2.10 9-Delete Options 112
- 6.3 Programmable Options 113
- 6-12 150966 114
- 6.3.1.2 Dialer Screen 116
- 6.3.1.3 Devices Screen 117
- 6-16 150966 118
- 6-18 150966 120
- 6-20 150966 122
- 6-22 150966 124
- 6.3.2.3 Zones Screen 125
- 6-24 150966 126
- 6-26 150966 128
- 6-28 150966 130
- 6.3.2.5 Areas Screen 132
- 6.3.3 Time Schedules Screen 133
- 6.3.4 Universal Schedules 134
- 6.3.5 User Profiles Screen 135
- 6.3.6 Users Screen 136
- Section 7 137
- Reportin 137
- 7.2 SIA Event Codes 138
- Reporting 139
- 7-4 150967 140
- 3 = Restore event 142
- 7-8 150967 144
- Open-Close 146
- 7-12 150967 148
- Alarm Restore 149
- Alarm Rese 149
- Door Access 149
- Exception OPCL 150
- Trouble OPCL 150
- Door Access Denied 151
- Door Exit 151
- Door Left Open 151
- 7-16 150967 152
- Section 8 153
- Troubleshootin 153
- 8-2 150968 154
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu SILENT KNIGHT 4821
(186 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce