SILENT KNIGHT 5700 Specifikace Strana 99
- Strana / 186
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Programming
151295 7-7
Heat Temperature Setting
Use this feature to set the temperature at which heat detectors will respond. The range is 135°
to 150° F. All detectors in the zone will respond in the same way.
The Model SD505-AHS Heat Detector is an absolute temperature device. This means that it
responds to an alarm immediately if the temperature in the zone goes above the programmed
temperature.
5. Enter the temperature at which the heat detector will respond.
Or
Use the or keys to scroll through the range or enter directly from the number keys
on the annunciator.
Then press .
7.3.1.3 Zone Outputs
Output groups and cadence patterns are mapped to events. They can be programmed to output
when an event occurs in a zone. Some system trouble events can be mapped for the entire
system. Section 6.2 of this manual contains a general explanation of mapping. The following
sections explain how to select mapping options.
Note: Use of multiple notification groups may not synchronize with each other.
Mapping to Zone Events
Eight types of events can occur in zones. For each event type, you can activate up to 8 output
groups or output group template, specifying a pattern for each.
Event types are:
• Manual Pull Alarm
• Water Flow Alarm
• Detector Alarm (heat or smoke detectors)
• Aux 1 and Aux 2 Alarm (user-specified alarm types)
• Pre-alarm
• Supervisory
• Trouble
- INTELLIKNIGHT 1
- MODEL 5700 1
- Installation Procedure 3
- Contents 5
- Section 1 11
- Introduction 11
- 1.2 About this Manual 12
- 1.3 Compatible Products 13
- 1-4 151295 14
- 1-6 151295 16
- Section 2 17
- 2-2 151295 18
- 151295 2-3 19
- 2-4 151295 20
- Section 3 21
- Before You Begin Installing 21
- 3.3 Electrical Specifications 22
- 3.4 Wiring Specifications 23
- 3.5 Board Assembly Diagram 24
- 3.6.1 Worksheet Requirements 25
- 3-6 151295 26
- 3-8 151295 28
- Section 4 29
- Control Panel Installation 29
- 4.1.3.2 Dead Front Removal 30
- 4.2 AC Connection 31
- 4.3 Battery Connection 32
- 4.3.1 RBB Accessory Cabinet 33
- 4.4 SBUS Wiring 35
- 4-8 151295 36
- 4.4.2 Wiring Configurations 38
- 4.5.1 Mounting the 5860 40
- 4.5.1.1 Flush Mounting 41
- 4-14 151295 42
- 4.5.1.2 Surface Mounting 43
- Installation 44
- 4.6.1 Selecting 5824 Options 46
- 4.7 5880 LED Driver Module 47
- 4.7.2 FACP Connection 48
- 4.7.3 LED Wiring 49
- 4.7.4 Dry Contact Wiring 50
- 4.8.1 FACP Connection 51
- 4.8.2 5865 Mounting 52
- 4.9 Configuring Modules 53
- 4.10 Telephone Connection 54
- 4.11 5211 Ground Start Relay 54
- 4-28 151295 56
- 4.12.2.1 Door Holder Power 57
- 4.13.1 Common Trouble Relay 58
- 4.13.2 Programmable Relays 58
- 4-32 151295 60
- 4-34 151295 62
- 4-36 151295 64
- 4-38 151295 66
- Section 5 67
- SLC Device Installation 67
- 5.2 Maximum Number of Devices 68
- 5-4 151295 70
- 5.4 Wiring Detectors 71
- 5.5 Addressing Devices 72
- 5-8 151295 74
- Section 6 75
- Programming Overview 75
- 6.1.1 Input Points 76
- 6.1.2 Output Points 76
- 6.1.3 Running JumpStart 76
- 6.2 Mapping Overview 78
- 6.2.1 Input Point Mapping 79
- 6.2.2 Output Circuit Mapping 80
- 6.2.3 Zone Event Mapping 81
- 6-8 151295 82
- 6.2.4 Mapping LED Points 83
- Software Suite 84
- 6.4.4 Editing Keys 86
- 6-14 151295 88
- 6-16 151295 90
- 6-18 151295 92
- Section 7 93
- 7.2 Modules 94
- 7.2.2 Adding a Module 95
- 7.2.3 Deleting a Module 95
- 7.3 Zone 96
- 7.3.1.2 Edit Zone Properties 97
- Alarm Delay Characteristics 98
- 4. Press 98
- 7.3.1.3 Zone Outputs 99
- 7-8 151295 100
- Programming 101
- 7.3.1.4 Cadence Patterns 102
- 7.3.2 Add Zone 103
- 7.3.3 Delete Zone 103
- 7.3.4 View Zone Points 104
- 7.4 Group 105
- 7.4.1.2 Edit Group Properties 106
- 7.4.2 Add Group 108
- 7.4.3 Delete Group 109
- 7.4.4 View Group Points 109
- 7-18 151295 110
- 7.5 Point 111
- 7-20 151295 112
- Table 7-4: Point Programming 112
- 7-22 151295 114
- 7-24 151295 116
- 7.6 System Options 117
- 7.6.1.1 Edit Accounts 118
- 7.6.2 Phone Lines 120
- 7.6.2.1 Dialing Prefix 121
- 7.6.2.4 Rotary Format 122
- 7.6.2.5 Line Monitor 122
- 7.6.2.6 Ground Start Relay 122
- 7.6.3 Sys. Event Outputs 123
- 7.6.3.1 Trouble Events 124
- 7.6.3.2 System Alarm Cadence 125
- 7.6.4 Miscellaneous Options 1 126
- 7.6.4.2 Low AC Report Delay 127
- 7.6.5 Miscellaneous Options 2 128
- 7.6.6 Miscellaneous Options 3 129
- 7.6.7 Edit Banner Message 130
- 7.7 JumpStart Autoprogramming 131
- 7.8 Computer Account 132
- 7.9 Access Codes 133
- 7.9.1 Profile Edit Menu 134
- Section 8 135
- System Operation 135
- 8.2 Menu System 136
- 8.3 Basic Operation 137
- 8.3.3 View Event History 138
- 8.3.4 Conduct a Fire Drill 138
- 8.3.6 Conduct a Walk Test 139
- 8.3.7 Conduct a Dialer Test 140
- 8.3.9 Reset alarms 140
- 8.3.11 View Status of a Point 141
- 8.3.14 Reset dialer 141
- 8-8 151295 142
- 8.3.16 Working with a Printer 143
- 8.4 Operation Mode Behavior 144
- 8.5 Releasing Operations 146
- 8-14 151295 148
- 8.6 Smoke Alarm Verification 149
- 8-16 151295 150
- Section 9 151
- Reporting 151
- Zone Events 152
- Section 10 155
- Testing and Troubleshooting 155
- 10.2.1 Event History 156
- 10.3.1 SLC Device Locator 157
- 10.3.2 SLC Multi Locator 158
- 10.3.3 I/O Point Control 159
- 10-6 151295 160
- Section 11 161
- Installation Records 161
- 11-2 151295 162
- Appendix A 163
- Compatible Devices 163
- A-2 151295 164
- A-6 151295 168
- System Sensor 168
- A-8 151295 170
- Wheelock 170
- A-10 151295 172
- A-12 151295 174
- A.2 Door Holder Device 175
- A.3 Two-Wire Smoke Detectors 176
- A-16 151295 178
- Appendix B 179
- Special Characters Lists 179
- B-2 151295 180
- Cut Along the Dotted Line 183
- Acknowledge 183
- © 2006 Silent Knight 186
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce